Archive for the ‘Straight Razor’ Category

Beornidas Carpentry Tools and Kamisori Razors – Jende Artisan Mall

May 28, 2017

Check out Beornidas’s hand crafted carpentry tools and kamisori razors at the Jende Artisan Mall!  Philipp Kirschfink, a craftsman / philosopher / bike messenger from the Netherlands using old school technology to create amazing works of art for carpenters and wet shavers alike!

Beornidas

Beornidas tools are inspired by tools from a wide range of cultures, including Japanese and Cree Indians.

Beornidas

They are designed with use in mind, and expertly crafted with an exquisite balance of rustic and beauty, and are all function.

Custom Damascus Straight Razor by Adam Grosskopf

December 5, 2016

We had the great fortune to meet Adam Grosskopf at the Sydney Knife Show this past August. He had a wide selection of beautiful straight razors at very reasonable prices. More importantly, they were actually properly honed up and in shave ready condition. We are very happy to announce that we have an Adam Grosskopf original damascus straight razor for sale on our Artisan Mall.

Adam Grosskopf Straight  079

Adam Grosskopf Straight #079

This beautiful straight razor is 5/8 and is hand forged using pattern welded 1084/15N20 steel. The blade is 1/4 hollow ground, with the edge overall length tang to toe measuring 5 ½”. Signed and serial numbered. #079. The blade also sports a micro clear Cerakote finish for easy clean and rust prevention. It has been honed by Adam and is shave ready.

The scales are laminated abalone shell veneer in black and clear acrylic with black and blue G10 spacers and a custom mosaic pin. The pivot is an adjustable stainless torx head screw with brass washers.  This razor comes with a hand-made deerskin pouch, certificate of origin, and a USB key with photos taken throughout the build and an electronic copy of  the Certificate of Origin. Don’t let this razor pass you by!

adam-grosskopf-079-3

 

Loading and Using the Jende Nanocloth Ultra Color Coded Strops –

September 20, 2016

We’ve done a quick and dirty video on how to load your Jende Color Coded Nanocloth Ultra Strops. These are the 4 micron 2×6″ with 4 micron CBN Emulsion and the 210×70 mm 0.25 Micron Poly Diamond Emulsion. Both strops and emulsions are color matched for easy recognition. 210×70 mm strops are designed to fit most stone holders as well. These strops are 3/4″ thick acrylic.

A special thanks to Mike Martinez of Martinez Blades and to Mark Reich of Reich Precision for allowing their razor and knife to make a cameo appearance.

Jende Nanocloth Ultra Strops – Color Coded for Your Pleasure!

September 9, 2016

We are happy introduce Jende Nanocloth Ultra, our newest innovation in stropping mediums!

jende-nanocloth-rainbow-big

Jende Nanocloth Ultra Rainbow

  • The Jende Nanocloth Ultra is a synthetic stropping material that has no weave, so feedback is the same in all directions. Other weaved strops tend to have noticeable resistance change feedback variations, like a rug when vacuuming, which can make you second guess your stropping stroke.
  • The Honeycomb structure is very consistent. The shape allows the emulsions to fill up the honeycombs, keeping more abrasive on the strop and off your knife. The shape also fills up and beads on the surface, giving a snow-shoe effect with even scratches when stropping.
jende-black-nanocloth-plain-400x

Jende Nanocloth Ultra – 400x

  • The depth of the honeycomb has little compression – less than leather in general.
  •  Because of the depth of abrasive in the honeycomb tubes, differential pressure can be used to give the strop more or less aggression by adding pressure for more aggression, and super light strokes to just tickle the edge for finish stropping.
  • The color-coded Acrylic base allows you to instantly recognize the grit strop you desire to use, saving time and confusion.
  • Laser etched to ensure long-lasting and clear identification marks.
  • Works equally well with our Jende Poly Diamond Sprays, Jende Poly Diamond Emulsions, and our Jende CBN Emulsions.

We are offing a huge variety of sizes on color coded acrylic, including 210x70mm and 2×6″ Bench strops on 3/4″ thick acrylic blocks, and for a full array of guided sharpening systems, including the Edge Pro (EP), Hapstone Sharpener, KME Sharpener, and Wicked Edge (WEPS).  Stropping will never be the same again!

Microscope Porn: How To Post It Correctly

August 1, 2015

With all the microscope porn on many of the sharpening and honing social media and forums lately, there needs to be a more standardized way to document the magnification. There are many available microscopes on the market, and the stated magnification levels are all over the map – from 3x to 1200x. Ironically, having the magnifications in these settings is irrelevant because we can enlarge and magnify pictures for various viewing needs, which often contradicts the stated magnification. It is therefore more important to know and state the actual area or size of the picture.

This tutorial will help to solve some of the uncertainties about knowing what the actual size of your pictures are rather than the so-called magnification. Please keep in mind that this is not in any way a comment on the quality of any of the scopes mentioned here. They are all very good, and extremely useful learning tools.

So, the easiest way to know your picture’s dimensions at a given magnification is to simply take a picture of a ruler under your scope, and state the dimensions when posting pics. This could be a USB scope, a scope attached to your cell phone, an optical scope, etc..

Below is a Veho at  20x. The pictured area is 6mm wide by 8mm high.

1 Ruler 20x ~6mm high

Ruler 20x ~6mm high

5 Ruler 20x ~8mm wide

Ruler 20x ~8mm wide

However, the Veho at 40x is 10mm high by 13mm wide! According to the magnification, the image sizes should be smaller (in theory, 3mm high x 4mm wide), but clearly the USB scopes don’t magnify the same as the scientific ones do. Hence, the issues with stating magnifications vs. stating the actual size of the pictured area.

2 Ruler 40x ~10mm high

Ruler 40x ~10mm high

6 Ruler 40x ~13mm wide

Ruler 40x ~13mm wide

To take it a little further, here is the Veho at 200x, which is 1mm high by 1.5mm wide. This is hardly a 10 times or even 5 times magnification of the 20x or 40x above.

3 Ruler 200x ~1mm high

Ruler 200x ~1mm high

7 Ruler 200x ~1.5mm wide

Ruler 200x ~1.5mm wide

And lastly, the Veho at 400x, just to drive the point home. 🙂 the picture is 0.75mm high by 1mm wide. Again, not the same ratio of magnification to the real size of the picture.

4 Ruler 400x 0.75mm high

Ruler 400x 0.75mm high

8 Ruler 400x ~1mm wide

Ruler 400x ~1mm wide

OK, so we get that part now. 🙂 On scopes with software packages, you can measure out the dimensions, and even set a “bar,” which represents a specified length, much like a map has a scale in KM or miles. In the example below, famed razor honer Dr. Matt has set his Dino Lite scope’s bar to 50.0 microns, which can be seen in the lower left hand corner of the picture. That means the entire area of the picture, no matter how large or small on your screen, will be approximately 300 microns wide by 250 microns high, or 0.3 mm wide by 0.25 mm high. Dr. Matt’s microscope is quite nice, you’ll notice there is also more information on the top tabs of the picture, including the “magnification” and screen resolution in pixels.

Dr. Matt’s bar is 50 microns

While Dr. Matt’s image as-is is self explanatory, if he didn’t have the bar or tabs and was citing this picture for others, he would say something like “This picture was taken with a Dino Lite 900, and the picture dimensions are 0.3 mm wide by 0.25 mm high.” This way we all know for sure just how close we are to getting our eyes sliced opened. 😀 BTW – stating the actual size of this picture makes Matt’s work even more impressive!

In conclusion, taking just a little time and a couple of pictures before hand to measure the actual size of your pictures will prove to be a more valuable asset to understanding what these pictures represent, and therefore make learning from them easier for the user, and for the rest of us in the peanut gallery. Thanks!

Diamond Bars by Ken Schwartz – For Buffers

November 17, 2014

We’re happy to announce that we now have Diamond Bars from Ken Schwartz! These specially formulated diamond bars are packed full of diamond abrasive, making them very fast, and very consistent. They also come in a wide range of grits – from 80 micron down to 0.10 micron! So if you’re removing rust from a blade, repairing chips, profiling or reprofiling, sharpening, or polishing the blade, these bars are essential.

Razor Honing with Jende Diamond Films

November 14, 2014

The new Jende Diamond Films are great for honing razors. I personally use the 1″x6″ size with PSA for all my razors, but you can use larger sizes, with or without PSA backing just as well! Here I go through the 45, 30, 15, 9, 6, 3, 1, and 0.5 micron films. For most razor applications, I recommend the Polishing Set from our website, which is the 15, 9, 6, 3, 1, 0.5 micron films (1K through 30K).

Jende Diamond Films – Using PSA and Non PSA

November 12, 2014

Our new diamond films come with the option of being PSA backed or non-PSA backed, and this video gives a quick how-to about securing your non-PSA film to a surface, and how to change the PSA backed film. This is on the 1″x6″ Edge Pro size films, but the methods will work on all sizes.

Diamond Films by Jende Industries

November 10, 2014

Abrasion resistant steels and ceramic knives are now an established part of the knife and tool world, and this requires diamonds in order sharpen them effectively. That’s why we are proud to introduce Diamond Sharpening Films by Jende Industries! We have 10 grits available, ranging from 80 microns to 0.5 microns (180 grit to 30,000 grit), and come in Wicked Edge Precision Sharpener (WEPS) size, Edge Pro size (1″x6″), 2″x6″, 3″x8″ and 3″x11″. They are also available with PSA and non-PSA backing.

2x6 jende standard set web

2″x6″ Diamond Films by Jende Industries

With a grit range that rivals that of some of the best sharpening stone series out there, our diamond films can handle profiling and repairs while bringing your edges to amazing heights of sharpness. Our films are also great for slip stone applications – they can be wrapped around dowels for sharpening serrated edges or the inside curvatures of turning tools, or used to polish the blade of old razors.

We’ve put together a few diamond film sets to choose from in order to get you started:

The Polishing Set includes one piece each of 15, 9, 6, 3, 1, and 0.5 micron films (1K to 30K grit), and is a comprehensive set that is geared toward general edge maintenance and regular repair work. Straight Razor honers will benefit greatly from this set, and those looking for shave ready knife edges will definitely impress!

The Standard Set includes one piece each of 45, 30, 15, 9, 6, and 3 micron films (320 to 6K grit), and is an “all around” set that can handle profiling and reasonable repairs. The 3 micron finish produces a mirror finish, and is “good enough” for most knife and tool applications.

The Coarse Set includes one piece each of 80, 60, 45, 30, 15, and 9 micron films (180 to 1,500 grit). This coarse set is meant for some more serious work, be it cleaning up scratches from belts or diamond plates, or for removing chips or reprofiling. The 9 micron film leaves a great “working sharp” edge that will hold up to abuse, and still do some serious cutting.

Jouhet Brevete Medialle 6/8 Forged Wedge – For Sale!

May 4, 2014

Our new section of used straight and DE razors for sale is slowly being populated! Our next razor is a wonderful hand forged Jouhet Brevete Medialle 6/8 Wedge with brand new African cedar wood scales.

We had trouble aging the razor, but given the facts of the steel type, lack of jimps, and hand forged shape, it was most likely forged as early as 1830 and as late as 1900 in the farming region of Jouhet, France. Our best guesstimate is 1880s, though. Either way, if you like wedges and smooth shaves, this is the razor for you. Please enjoy the intro and shave below!